NTV viaccess conditional access plus incorrect configuration. Setting up the NTV-Plus antenna yourself. Tuning the antenna "NTV-Plus Vostok" on different TVs

Many users prefer to install satellite equipment on their own. What you may encounter in such cases, what subtleties accompany the installation process, how to set up NTV Plus channels - you can find out below.

The first thing to do to install NTV Plus is to install and mount all the necessary equipment. If the user does not use the services of the company's specialists, but decided to do it on his own, then it is important to observe several basic rules:

the direction of the plate is south. The reason is that the main satellites of the company Eutelsat 36A and Eutelsat 36B / 36C are located above the equatorial zone of the planet. To make the process easier, you can use an ordinary compass. The angle of the satellite direction is in the range of 17-38 degrees, depending on the equipment manufacturer, since the provider uses the services of several;
another very important parameter is the clean area in front of the plate. Pay attention that in a straight line in front of it there is no interference, such as trees, high-rise buildings, and so on, as they can greatly degrade the quality of the received signal;
fastening the bracket should be given no less attention, and installed as securely as possible, since otherwise it will loosen over the years, the plate will break, and the image quality will greatly decrease;
it is not worth saving when buying a cable - its resistance to various weather disturbances is extremely important.

Antenna

And now, the installation is over, everything is fine, and you can proceed to the next stage - tuning the NTV antenna.

The converter cable is connected to the receiver, and the receiver itself is connected to the TV. It is important to follow all instructions from the manufacturer, this will help to avoid damage.
Slowly and carefully rotate the antenna dish vertically and horizontally towards the location of the satellite until a picture and sound of excellent quality appears. To make the process faster and more comfortable, it is better to do everything together - one turns the antenna, the other coordinates by phone.
And now, the screen pleases with a high-quality picture, the next step is to activate the command "received signal level" on the receiver. Try to make the scale as complete as possible.

With the proper patience, setting up an NTV satellite will not cause problems.

registration

Next, you need to register installed equipment, CL module and access card on the official website ntvplus.ru. After filling in all the necessary data, if everything is done correctly, on specified mail a letter will come with a key to activate the profile, after which access to the registration of the contract will appear in the office.

Upon completion of registration, the card is automatically activated within 24 hours.

Receiver

The receiver is one of the most important components, without it it will be impossible to watch satellite TV. The range of the company has many different models of set-top boxes, so for a number of nuances, the setup process may differ. Some of the most popular receivers are shown in the figure below:

Debugging channels

To tune NTV channels, you can use two available options - manual and automatic tuning.

Autotuning is easier - the command “search for channels” is selected in the menu, and the set-top box will find and install everything on its own.

With manual NTV tuning, everything is not so simple, but with due care, everything will go well:

Enter the default settings in the receiver settings section. There you need to enter the "channels" menu, then "antenna" and "satellite settings".
If the prefix asks for a password, try entering four zeros, this is a standard password.
A tab will appear in which we leave only the EutelsatW4 36E satellite, uncheck the rest of the checkboxes. If the tuner does not allow the procedure, you need to pull out the access card.
The next item is transponder settings. Install top level Lnb is like 10750 and the bottom is zero. The settings are 12130 R.
The last stage - in the manual settings section, select the above transponder and click on "network search". The process is quite lengthy, so there is no need to worry. Upon completion, depending on the selected tariff plan the desired number of channels appears.

Setting up LG and Samsung TVs with CAM

LG and Samsung TVs have an installed CAM module, so the setup process proceeds a little differently. Let's take a look at a Samsung TV as an example:

In the menu, select the section "broadcast".
Select EutelsatW4 36E from the drop-down list of antennas, save.
Go to the "LNB settings" tab, select any transponder there. Turn off DiSEqC mode and tone 22 KHz. The upper LNB is set to 10750, the lower one is 9750.
On the remote twice press the button"Return", and go to the manual search for TV channels.
Once again, select the EutelsatW4 36E satellite, after which we look for 11900 (V / R) 27500 in the transponder list, select and save.
We select the command "network search", go to the item "broadcast" and select "change channels". Using the "change number" tab, select the channel to which you want to set the number.
Then we go to "sorting", and distribute the found channels depending on the categories - TV, music, radio.
Installation and commissioning is complete, pleasant viewing.

For LG TVs, the process is almost identical, you only need to change the transponder value, as in the photo below:

Outcome

Tuning transponders and NTV frequencies with due care does not pose any problems. If difficulties and problems arise, it is better to use the services of the company's specialists, this will help save both time and nerves.

It is difficult to find a house without a single TV set. But free channels it is one thing and quite another when it comes to satellite pay TV. The number of NTV Plus paid channels depends on the package that the user paid for. But in order to get them, a small setting is required, which can be done on your own or by contacting the service for help.

Then you will have the opportunity to watch your favorite films, sports programs, programs of domestic and foreign production, and much more. In addition, it is not difficult to find out which settings are correct for NTV Plus, since the official website contains all the instructions, and not only general ones, but also depending on specific models receivers.

Setting up satellite equipment

Much depends on how the equipment is configured, including the signal quality. Therefore, you need to understand some of the features of the installation of equipment, if the user decided to save money, and not order the services of a wizard who will install and configure everything himself. So, here are the instructions to follow:

Since the NTV satellites are located above the equator, in order to catch the signal, you need to direct the dish to the south side. In order not to guess where it is, take a compass or use the online compass by downloading this application to your smartphone. But as for the angle of inclination of the satellite dish, depending on the terrain and manufacturer, it should be somewhere in the range of 17-38 degrees;
Examine the area carefully to determine if there is interference. It is very simple to do this - if the view in the right direction is good, then everything is fine, and if not, then you need to find another place with a better view;
Try to fix the cymbal as tightly as possible so as not to confuse the settings. Each time it gets boring to tune channels quickly, so it's better to use a reliable bracket and enjoy satellite TV from NTV;

And of course, in order for any TV channel to work normally, it is important to choose the right cable that will be resistant to weather conditions. Snow, rain and other precipitation will fall on it, therefore the equipment must be reliable;
The cable must be connected to the receiver, and the receiver to the TV;
Even if you do not know the exact settings, you can catch them yourself by turning the dish horizontally and vertically until the image appears on the TV screen. When there is a picture, you need to look at the signal reception level - it should be above 50%;
Log in to the site and get access rights to various packages. The operator helps newcomers to fully enjoy the broadcast. The account of the newly registered user has a small amount that pays for the broadcasting of the standard package - all that remains is to tune the channels.

When the operation "Registration of the contract" is completed, the access card will activate its work, and within 24 hours a person will be able to see what the provider has prepared for new users.

Configuring NTV Plus channels

At the moment, there are several ways to configure channels from the NTV Plus provider. There are two most popular options.

An automatic setup that looks like this:

Enter the menu using the remote control;
Find the subsection "Channel search" there;
Click it and follow the search status. When it ends, all channels will start showing.

Setting up the TV manually has the following specifics:

First you need to reset the tinctures. This is done in this way: "Settings" → "Default setting" → "Channels" → "Antenna" → "Satellite settings";
The prefix will ask you to enter a password. Feel free to enter four zeros, but only if this option has not been changed;
After that, when manually searching for TV channels on NTV Plus, you need to uncheck the checkboxes in front of the satellites, which are allowed by selecting only the one with which NTV Plus works. V this case Is EutelsatW4 36E. Sometimes it happens that the service in question is blocked by the tuner itself or the TV, and in order to open access, you just need to remove the access card and insert it back;
Next, you need to configure the transponder. Here are the settings: 12130 R and Lnb levels (bottom = 0; top = 10750).

When the whole procedure is completed, you can proceed to the final stage: Select the transponder and set the command "Search in the network". After that you have to wait, because the setting takes a long time. But if all the changes were correct, then in half an hour you will have all the paid TV channels working.

Configuring NTV Plus Vostok channels

The NTV Plus television company is one of the most popular in Russia, but there were interruptions in broadcasting in the eastern part of the country, which were resolved with the help of the new package and the Express-AT1 satellite. The change took place in 2014, so that in 2017 users can enjoy excellent broadcasting of popular channels and not only for several years.

If, for some reason, your equipment does not want to receive the signal that comes from this satellite, you can manually search for TV channels after entering the settings. This is not so difficult, since the reconfiguration can also be done manually. Television will soon start operating in standard mode delighting the audience full package TV channels.

So, in order to access the package, you need to check the satellite settings, and if they are not there, then first enter this satellite, and then fill in the broadcast parameters. Instructions on how to set up channels are simple:

Open the receiver settings via the remote remote control and the "MENU" button;
Turn on the search for NTV channels;
Go to "Settings" - "Installation" - "Password" - "Search mode" - "Enable";
Enter the transponder parameters: frequency - 12475; polarization - to the left; transmission speed - 27500; broadcasting - DVB-S2; modulation - 8PSK; FEC: 5/6;
Check the "Level" and "Quality" of the signal. Click on "Search" again;
Wait for the results and save them.

1. How to manually tune a TV with a built-in satellite receiver to the NTV Plus or Tricolor TV satellite?

For the sample, we chose a 2015 LG TV on operating system"WEB OC". Basically, the manual tuning algorithm for other TV models is not much different.
So. The TV is connected to a tuned and functional satellite antenna, and is tuned in the TV reception mode - "Live TV". On the screen we see, respectively:

On the remote we press "Settings" or "Q.MENU".
Choose from the menu that appears "Advanced settings"

A menu of full settings appears, where we select "Channels", "Search for channels".

After clicking on "Channel Search", select there "Manual search" and "Satellite"(if there is still no additional terrestrial antenna or cable TV is not connected).

The most important search menu appears with parameter settings.

Let's say you need to find all the channels of the operator "NTV Plus" and only him!
We select the satellite "Eutelsat 36".
A very important parameter: "LNB frequency" (in different TVs can be called a little differently: "intermediate frequency", "upper and lower frequency separately" ... It does not matter.
We put there always and everywhere 10750 ... For in other models 10600, 9750, 5100 ... may be offered, but we put only 10750 everywhere.
Next, select the "Transponder" (or the frequency of one of the satellite transmitters). Since we need NTV Plus channels, we take any frequency from the section (if you need to tune to Tricolor TV, then we take from the section What frequencies and parameters of Tricolor TV channels?).
We have now chosen a transponder with a frequency of 12130 MHz, right-hand circular polarization.
Next, we monitor the scales of the level and quality of the signal. If everything is installed correctly, then they should be over 70%.

We make the "Search network" parameter enabled! Then the TV will automatically find all the others according to information from one transponder installed by us and only from the operator "NTV Plus" (and not yet ~ 250 channels of unnecessary "garbage" from Tricolor TV, etc., which happens in the automatic search mode).
Some TVs do not have network search mode. Then you will have to manually scan each transponder from the list (referred to above) separately.

As a result, we see that the TV has found all 17 transponders of the NTV Plus operator.

Click "Finish", exit the settings menu and look at the channels we need in the presence of the CI + module with activated card access.

P.S. If in the end you suddenly realize that it is difficult to edit channels there, create and switch favorite lists, inconvenient TV Guide, etc. (which is inherent all primitive satellite receivers built into televisions) and this is so annoying that we are ready to use 2 remotes (the first one is for turning on / off the TV, the other for everything else), then we recommend purchasing for your access module any of the specialized satellite receivers of the line we offer ... Which, by the way, are often purchased by TV owners high class which, of course, have a built-in satellite receiver and a slot for the CI + access module.

2. The TV (receiver) with the CI + CAM NTV Plus module displays on the coded channel "Incorrect equipment setting. Please contact your operator". The service has been paid for. What to do?

It is necessary to reboot the CI + CAM module ("factory reset", "factory reset")

On the example of the Samsung TV.

We go to the TV menu

We select the command "System"

We select the command "Settings"

We select the command "Common interface"

We select the command "Menu CI"

By selecting the "Information" command, you can view information about subscriptions - have you run out of money in your account? Then, perhaps, the problem is not in the module, but in the payment.

But, initially we assume that you are sure about the payment for services. Therefore, click on "Settings"

We select the command "Factory setting"

A menu appears asking:

Click "OK" to confirm and wait for the module to reboot. After that, we leave the device turned on on the encoded channel and wait for the picture to appear.
The picture will not appear immediately. The wait can be several hours.
All operations are carried out at your own risk. If you are not sure (and there is a possibility that you will drop something else, very important there), then it is better to contact our store for setting up the module and the card.

3. What are the frequencies of Tricolor TV? What are the frequencies of "NTV Plus"? What are the open channels on the satellite from which Tricolor TV and NTV Plus broadcast? Channel parameter information - how to manually tune channels. What channels are there on the satellite?

Tricolor TV and NTV Plus are broadcast from Eutelsat 36A / 36B satellites, which are "hovering" in geostationary orbit at an altitude of ~ 30,000 km strictly above the Equator at 36.0 ° E (east longitude). Taking a map, you can roughly determine the direction, azimuth from Kaliningrad towards this satellite position.

Setting up NTV PLUS begins with the installation and installation of equipment. If they are carried out independently, then it is important to observe the following rules:

The satellites NTV + Eutelsat 36B / 36C, Eutelsat 36A are located above the equator, so the dish should be directed to the south. The exact direction can be determined using a compass. The angle of direction of the satellite is approximately 17 - 38 degrees. It depends on the manufacturer of the dish, the satellite television operator NTV has several of them.
In order for the satellite dish to receive an excellent signal, it is important to take into account the overview of the territory during installation; interference in the form of vegetation, tall buildings is not permissible. Failure to comply with these requirements may result in signal transmission problems.
The bracket is attached firmly and securely, otherwise, over time, the saucer will break, the direction will change, all this will affect the quality of the signal.
It is not recommended to save on the cable, it must be resistant to different weather conditions.

The next step is setting up the NTV satellite dish.

, myself . To avoid malfunctions or damage to the equipment, all recommendations specified in the manufacturer's instructions must be followed.
Turn the mirror slowly and carefully satellite dish in the horizontal / vertical plane towards the location of the satellite. Purpose: to achieve the appearance of the image on the TV.
After the picture has appeared, it is necessary to activate the command "RECEIVED SIGNAL LEVEL" on the receiver. For a good television picture, the scale should be as high as possible.

Online registration of access card and CL module

To register this equipment, authorization is required on the official website of the operator.

If the data is filled in correctly, on email you will receive a letter confirming the activation of the profile. After that, the operation "Registration of the contract" will be available to the subscriber on the site. After the conclusion of the contract, the activation of the card will occur automatically within 24 hours.

How to configure the receiver for broadcasting NTV channels

Without this device, satellite TV viewing is impossible. The television company NTV PLUS offers various models of TV set-top boxes, so the setting of the equipment may vary.

Models of NTV + receivers for watching television from the Eutelsat 36B / 36C satellite offered by the provider in 2017:

Digital interactive set-top box VA1020;
NTV-PLUS 1 HD VA;
HUMAX VAHD93100S;
Humax VA-4SD;
Humax VHDR 3000S;
Sagemcom 87-1HD;
Sagemcom DSI74 HD;
Opentech OHS1740V.

The VA1020 set-top box is the most modern development, it went on sale in the fall of 2016. New subscribers of the company have the opportunity to purchase at a discount. The promotion is valid until the end of January 2017.

Channel setup

There are two options for configuring channels: automatic way and manual setting... In the first method, select the "CHANNEL SEARCH" item in the setup menu, if the equipment is configured correctly, all channels will appear soon.

Manual search is a more complicated process:

Resetting the preset settings - go to the menu, select the section "SETUP" → "DEFAULT INSTALLATION" → "CHANNELS" → "ANTENNA" → "SATELLITE SETUP".
When prompted by a TV set-top box for a password, enter a number consisting of four zeros. If the password has been changed, the changed option is required.
In the tab that appears, uncheck the boxes next to the satellites allowed by default, leave EutelsatW4 36E. If this procedure is blocked, you need to pull out the access card from the tuner.
Then it is important to tune the transponder.
Settings: 12130 R and Lnb levels (lower = 0; upper = 10750).
The final stage. After entering all the data in the "MANUAL SETUP" section, select the previously recommended transponder and set the "SEARCH ON NETWORK" command. The operation can take quite a long time, at the end all available channels will appear. The quantity depends on the package selected by the user.

Instructions for setting up Samsung and LG TV models with CAM - Module

Step-by-step setup of NTV PLUS for Samsung:
Go to the menu and select the "BROADCAST" item
Choose EutelsatW4 36E from the proposed antenna types. Save data.
Go to the "LNB SETTINGS" tab, and select any transponder. Set DiSEqC mode - off. Lower LNB = 9750. Upper LNB = 10750. 22KHZ tone off.
Make two clicks on the "Return" button on the remote control.
Go to manual channel search.
Select the EutelsatW4 36E satellite again, then find the number 11900 (V / R) 27500 in the transponder list, press the OK button.
Set the command "SEARCH ON NETWORK".
Then in the section "BROADCAST" select "CHANGE CHANNELS". Select the channel to be given a number using the NUMBER CHANGE tab.
Select the "SORT" item and sort the channels into categories: radio, music, TV.
Channel setup and installation is complete.

For LG, the setting is similar, but the transponder value changes according to the photo.

class = "eliadunit">

First, we reset the TV to factory settings. Menu> support> self-diagnostics> reset> ok. After rebooting, go to menu> channel> antenna> select the value "satellite".

We remove the jackdaws from all the satellites that are installed by default (if this fails, you need to remove the CAM module from the slot and reset the TV again), scroll through and select the EutelsatW4 36E satellite, select the transponder in the LNB settings 12130 R, lower gene. LNB - 0, top - 10750.

Then go to "manual settings", look for a transponder 12130 R, turn on "network search" and click "search".

We are waiting for the completion of the search for NTV-Plus channels and save the found channels.

Then you can sort the channels at your discretion (it is better and more convenient to do this using Samsung programs Channel List Editor)

If the satellite There is no EutelsatW4 36E in the settings, we do this:

We choose " User sat 1".

Create your own satellite (put a bird in front of it) and save.

We go into the LNB settings, set everything as in the screenshot.

We do not put anything in the "transponder" section, we will add them manually.

The section "transponders" will be empty, select "create".

We need transponder frequencies, flow rate and polarization type for each channel packet. I will list:

DVB-S2 / 8PSK

Attention!!!

these frequencies have SR 27500 FEC 3/4
Set the correct polarization type ( L) or ( R)

Now we create all these transponders (continue).

We drive in the frequency (with numbers directly from the remote control), the transmission speed (also from the remote control) and select the type of polarization (L or R). We press "save".

The name of the network "NTV-PLUS" appears, press "search" and "OK".

The channel package for this transponder has been scanned and saved in the TV's memory. Then everything is repeated for each subsequent transponder. In the same place, in the "manual setting" menu, we press "scan" in the "transponder" section, create the next one with our data, and so on. All previous scored and scanned transponders with settings and channels are saved.

As a result, we get all (together with radio) NTV-PLUS channels.

Categories

Popular