Two TVs from one antenna with an amplifier. The right way: how to connect two TVs to one antenna. But making a high-quality connection without a signal divider or other device will not work

A TV has long been considered an attribute of luxury, so every second family has at least one or two such devices. If the first device is located in the bedroom, then the second can stand anywhere, for example, in the hallway, living room, in the kitchen or in any other room. Owners of several devices sometimes need to connect two TVs from one antenna.

general information

Trying to understand how to connect 2 TVs from one antenna, you need to understand the general principle of such a procedure, the required tools, as well as the main steps. To connect devices, you need to use several available tools and parts. Among them:

pliers;
side cutters;
kitchen knife.

The first step is to purchase a TV splitter or splitter that can split the antenna signal into two streams. On one side of it there is an entrance, and on the other - outputs for connection to the receiver.

After that, you need to take 5 connectors that coincide in thickness with the outputs on the splitter, as well as adapter plugs. When choosing an antenna cable, it is recommended to give preference to high-quality and proven models, for example, RG-6 or PK-75.

When choosing a splitter or splitter, it is important to consider the number of outputs, because three-way models are intended for the interaction of three devices, but not two. If such an option was purchased, but there are only two TVs in the house, it can be closed with a special resistor with a resistance of 75 ohms. In this case, you need to read the step-by-step instructions on how to connect 2 TVs to one antenna.

The connection procedure itself is not something complicated, so even an inexperienced user who does not have any radio engineering skills can carry out such manipulations without outside help.

Splitter types

The main purpose of the splitters is to match wave impedances, fix a stable signal, and combat all kinds of noise and interference. A correctly chosen splitter guarantees high picture quality and prevents any distortion. But in order to make the right decision at the selection stage, you need to know what types of such devices are, what they are intended for and what properties they have. There are two main types of splitters available on the market:

with an active form of work;
passive.

Such devices can have one input and a pair of outputs. Most home TVs use models with two or three outputs, although the number is not limited. Splitters evenly distribute the signal from one antenna, so if the input signal intensity is 12 dB, then the TVs will receive half of this value, that is, 6 dB each. If the antenna crab is equipped with three outputs, then the received TV signal will be 4 dB. Passive models can use transistors or transformers.

As already stated, the number of outputs in the splitters can vary from two to eight... If we are talking about buying a model for two TVs, it is better to make sure that in the future you will not have to connect several more receivers to the same antenna. It is also important to take into account the attenuation level possessed by the splitter, because the lower it is, the better quality Images.

Splitters with a built-in RF amplifier belong to the active group. They are able to capture a high-quality signal and raise it if necessary. But for such a device to work, you need to turn on the power. It can be a separate unit or a cable connection.

Device selection

Interested in how to connect two TVs to one antenna, you must first purchase a splitter. There are a lot of such products on sale, so there will be no difficulties in choosing the right model. In this case, the principle is appropriate: the more expensive, the better.

At the purchase stage, it is important to take into account your skills in working with a soldering iron. If they are present, then you can buy a soldered splitter, since it is characterized by significantly less signal loss and the ability to maintain transmission quality.

If you didn't have to work with soldering devices, it is better to opt for a conventional splitter. However, in this case, it is necessary to pay attention to the type of cable with which the device is equipped. The best option is a splitter with a standard connector for coaxial wires.

Having decided on the choice, it remains to find suitable connectors. In most cases, for this purpose, user-friendly F-interface, which is a wrapping adapter.

Besides, it is important to choose a suitable location for the splitter keeping the correct distance between it and the TVs. Experts recommend choosing an approximately equal distance, while the cable for the antenna should not twist and be stretched. You can not stretch it with a shortage of footage or, conversely, twist it excessively. It is important to pre-calculate the distance between the splitter and the TV, as well as get rid of the excess.

At the stage of preparing the cable, you need to cut it in such a way that it can freely reach the splitter. Cut off the old plug along with the remaining piece of wire. After that, the cable must be cut for installation in the F-connector.

First of all, you need to cut the wrapper to the braid (about 15 millimeters from the edge), and also fold the edges. The insulation layer should protrude slightly, and the vein end should protrude 4-7 mm. You need to prepare the cable for the adapter-plug with a kitchen knife and side cutters.

Features of the procedure

When figuring out how to connect multiple TVs to one antenna, you need to follow step by step guide. To successfully complete the task, you must follow the following rules:

In the correct order, it is necessary to connect the cables to the splitter, and do not tighten the F-connector too tightly, as this can cause the main conductor to fall out of the adapter. Many people do not change the location of the splitter, leaving it somewhere under furniture or near the baseboard. Experts advise to securely fix the splitter, otherwise it may be damaged by contact with children or pets. The splitter can be hidden behind a false panel.

If follow step by step instructions and correctly perform each stage, then a clear picture should appear on the TVs without interference or deviations. If something is done wrong, the so-called snow will appear on the screen, which indicates a partial loss of signal or a complete lack of image.

Satellite TV and Polish antennas

If some stage of splitter installation is performed incorrectly, loss of image quality may be observed. A similar phenomenon often appears when working with a satellite dish, when the splitter picks up part of the signal to itself.

To eliminate an unpleasant problem, you need to purchase a splitter with a built-in amplifier. Its cost may differ significantly from the price of conventional models, but this is justified by the maximum efficiency. In addition, all splitters with an amplifier support different gains, because under some circumstances, a strong signal becomes as unnecessary as a weak one. And if you take into account the fact that sometimes it aggravates the problem, then it is better to refuse such an option.

If a classic Polish antenna is installed in the room, then in order to improve the signal, you can connect an amplifier with a power supply. This will make the picture look good and prevent snow from appearing on the screen. ... To solve the problem, you must follow the following rules:

In the familiar circuitry, a few changes need to be made to the amplifier.
Remove the F-type connector from the input, and in the space that appears, install the plug that comes with the antenna.
Next, you need to install the adapter with the antenna socket and connect the amplifier.

By completing such measures, you can significantly increase the gain. To permanently get rid of the poor picture quality on two TVs, it is better to buy two antennas at once.

Signal amplification methods

For many TV owners, after connecting several TVs to one antenna, the quality of the displayed picture deteriorates greatly. This is due to the principle of the splitter, which only splits the signal into several streams. To eliminate the negative phenomenon, it is necessary to purchase a special amplifier that works on the crab principle, but has several resistors and an amplifying microcircuit.

For such a device, it is necessary to equip a separate power supply, therefore, when performing installation work, you need to consider the location of the outlet or extension cord. It is recommended to install the amplifier on short distance from the antenna, and from it make branches to the desired part of the room. Experts say that it is much wiser to abandon the splitter and give preference to amplifiers. Such a purchase will be more expensive, but it will be justified by the high quality of the transmitted signal.

To prevent all kinds of interference on the screen and improve the signal, special ferrite rings can be placed on the TV cable. They are placed at the very end of the cable near the antenna input. These noise cutters are found on laptop power supply cords and are designed to combat poor signal quality.

There are others no less effective ways amplification of the television signal, but much depends on the antenna itself. In order not to think about how to get rid of the problem of low picture quality when connecting several TVs to one antenna, it is better to buy in advance good device and prevent such troubles.

The process of amplifying the signal from the antenna to two TVs is carried out through the interaction of two devices - a preamplifier and a distribution amplifier. According to the principle of operation, these nodes practically do not differ from each other, but some differences are still present. The preamplifier is located on the antenna and is intended to amplify the signal. It is used for a long coaxial cable and is fixed between the antenna and the splitter.

The amplifying device is mounted in front of the splitter and is used to amplify the divided signal, for example, for two or four televisions. Most amplifiers work in exactly the same way as splitters, so it makes sense to choose just such a device and not buy a splitter.

Connecting two, three or more TVs to one antenna is not difficult. Even an inexperienced beginner with no professional skills will be able to carry out such a manipulation and achieve good results. The main thing is to follow the step-by-step instructions and take into account the recommendations of experienced specialists.

Very often a second TV set appears in one family. In this case, there is only one antenna. The question arises: how to connect two TVs to one antenna? There are ways to allow one antenna to be used on two TVs or more.

Several parts are required to connect:

two-way splitter (splitter). This is a device that allows you to split the signal from the antenna into two or more streams. It has an input on one side and two or more outputs on the other - for connecting TV sets.

5 connectors corresponding to the splitter;
2 plug adapters;

We will try to tell you about the connection in such a way that even someone who does not understand radio engineering at all could cope with the task. This is done step by step like this:

Choosing the details. The first step is to buy a splitter. They are different, including those that need soldering, and those that do not. If you know how to solder, then it is better to take those that involve soldering. This connection is always more reliable than any other, it gives less signal loss, preserves its quality.

If you do not have the skills of soldering, then you need to choose the appropriate splitter, as well as suitable for a certain type of cable. A splitter with built-in jacks for coaxial cables is a safe bet.

After choosing a splitter, select the appropriate connectors. Now F-connectors are very popular due to the fact that they are reliable, easy to install.

Choosing a place for the splitter. It is optimal to position the device so that the antenna cable can freely reach it and, if possible, have the shortest distance to both TVs.
Cut the existing antenna cable. It is necessary to cut so that the cable can freely reach the splitter. Together with a piece of cable, the old plug is cut off.
Cutting the cable and installing the F-connector.

For those who know how to solder, there is no point in telling how to cut the cable and solder it to the splitter - they know it themselves. The rest is written for the average user who is not familiar with the radio business.

So, we cut the cut end of the wire, as shown in the figure: we clean the edge, wrap the braid. The insulator of the middle conductor should protrude slightly, and the middle conductor itself should protrude at least 5 mm. An ordinary kitchen knife is a tool for removing insulation from a coaxial cable at home.

Install the F-connector. It is also called wrap because the connector is wrapped around a soft wire. The connector for connecting the cable and splitter is ready.

We cut off two pieces of wire so that there is enough length for each TV.
We mount the F-connectors in the same way for connecting TV cables and splitter outputs. Do the same on the other ends of the cables.

As a result, we use all five connectors, including:

one from the antenna to enter the splitter;
two television sets for exits from it;
two TV free.

We connect the connectors to the splitter.

We connect two free connectors with adapters. An adapter is a device that holds an F-connector at one end and a coaxial plug for connecting to TV sets at the other end. This device is generally referred to as a plug.
We turn on the television sets. Checking how both receivers work. If everything is done correctly, then the image should be normal. Now you can easily enjoy an excellent picture on two receivers at once, without interfering with each other.

According to the diagram below, you can see the path by which you need to connect 2 TVs to one antenna:

How to connect two TVs. Connecting a TV cable

Dear visitors!!!

Many of us have a need to connect two TVs to one TV cable. For example, doing our own thing in the kitchen, or relaxing in the hall, we can watch this or that television channel and be aware of all the events taking place in the world. This opportunity is provided to us by connecting a TV cable through a TV signal divider.

TV signal divider

Connecting two TVs to one cable is done through a TV signal divider. When purchasing a signal divider, the very diagram of such a connection is shown on the case itself. So, how to connect two TVs to one cable from one antenna. Let's start with the TV cable itself.

Connecting a TV cable

You need to first decide where you will have a cut of the television cable for the further connection of two television cables to the TV signal divider. You will get one common TV cable that receives a signal from television antenna connected to the TV signal splitter jack.

How to connect the plug-to the TV cable

It is additionally necessary that another TV plug is available. To solder a TV plug, you need:

remove a small part of the cable insulation;
untwist the outer sheath of the cable;
twist the braid and pickle with flux for soldering;
solder the outer braid to the outer contact of the plug.

The inner wire of the television cable is preliminarily after moistening it with a flux for soldering, soldered to internal contact plug.

The connection of television cables with a television signal divider is carried out with the initial removal of a piece of cable insulation.

Now, let's get acquainted with the diagram of connecting two TVs - to one antenna.

Wiring diagram for two TVs - to one antenna

Shown here are the connections from one common TV cable:

for two TVs;
for three TVs.

The signal from the TV antenna is distributed through the TV signal splitter and fed through the cable to the TV jack.

You should not sharpen your attention with a connection through a TV signal divider. The second connection option looks through a junction box.

Junction box

In this embodiment, a method for connecting two TVs is clearly shown, where the cable wires can be connected in a junction box. The connected contacts of the signal wires of the television cable are etched and soldered with soldering tin. The connection of two television cables to a common cable is parallel. Difficult, as you have seen, there is nothing here.

That's all for now. Follow the rubric.

zapiski-elektrika.ru

How to connect two TVs to one antenna: the order of work

Almost every average family has a second TV: in the kitchen, in the bedroom, and sometimes in the hallway. Therefore, for many, the question of how to connect two TVs to one antenna is quite acute. There are not so few ways, but we will focus on the simplest and at the same time effective options.

So, let's figure out how to connect two TVs to one antenna, what tools are needed for this, and also outline the main stages of this process.

What is needed

In the process of connecting, we will need a few details. Pliers, side cutters and an ordinary kitchen knife will act as tools.

First of all, we need a TV splitter, or a splitter. This device is able to split the signal from the antenna into several streams (in our case, two). That is, on one side there is an input, and on the other, there are several outputs for connecting to the receiver.

Next, we need five connectors that coincide in diameter with the outputs on the splitter, as well as two adapter plugs. Choose the antenna cable at your discretion, but it is better to stop at even more expensive, but proven options - RG-6 or domestic RK-75.

It is also worth considering that when buying a splitter, be sure to check the number of outputs. For example, three-band models are designed to connect exactly three TVs, but not two. If, for some reason, a splitter for three receivers is at hand, then the unnecessary output can be drowned out with a special ballistic resistor with a resistance of 75 Ohm. Be sure to pay special attention to this point before connecting two TVs to the same antenna.

In principle, the connection process itself is simple, and any user can handle it, even one who has never heard of radio engineering. For clarity, we will divide the whole process into separate stages.

Choosing a TV splitter

First you need to buy a splitter. On store shelves, you can find a large assortment of models from different manufacturers... A simple rule applies here - the more expensive the better. But there is another one here important point, which is worth paying attention to before connecting two TVs to one antenna. It's about soldering. If you have the skills to work with a soldering iron, then it is better to give preference to models with soldering. Such splitters, and this connection in particular, are always more reliable, they imply significantly less signal loss along with maintaining quality.

In the event that a soldering iron is something incomprehensible for you, then you can take an ordinary splitter, but again, taking into account the type of cable available - or vice versa. The best option is a splitter with standard connectors for coaxial wires (cable for an antenna, type RG-6 / RK-75). After you decide on the splitter, you need to choose the appropriate connectors. The most popular is the convenient, reliable and easy-to-install F-interface (wrapping adapter).

Also, special attention should be paid to the location of the splitter. The best option is considered to be approximately equal distance from the splitter to both TVs. It is important that the cable for the antenna is free of tension and does not twist, that is, you do not need to try to stretch it due to lack of footage, or, conversely, twist it. Calculate the distance from the splitter to the TVs in advance and cut off the excess.

Preparing the cable

The cable must be cut so that it can freely reach the splitter. As a rule, the old plug is cut along with a piece of wire. Then you need to strip the cable for installation in the F-connector.

First, we clean the edges, that is, we cut the wrapper to the braid (about 15 mm from the edge) and bend the edges. The insulating "fur coat" on the cable should protrude slightly, and the vein end itself should protrude at least 4-7 mm. The entire procedure for preparing the cable for the adapter-plug can be performed using a kitchen knife and side cutters.

Features of the procedure

It is also important to know that the cable sheath should not touch the center conductor in any way. Such an error is fraught with partial or complete loss signal. Such problems most often arise with cables of the SAT 703B and DG-113 brands, where each layer is very thin.

Next, we mount the F-connector on the cable. He got the name "wrapping" due to a specific installation, where the plug is simply screwed onto the wire. A similar procedure must be done on all cables - and as a result, you get five connectors: one for the antenna, two for the output and two for the input.

Connection

In the right order, we connect the cables to the splitter. Do not overtighten the F-connector, as this may cause the main conductor to fall out of the adapter. Most users leave the splitter as it is, that is, dangling somewhere on the baseboard or under the nightstand. Experts recommend that the splitter should be properly secured to avoid breaks and wire loss. If there are children in the house, then this item is mandatory, plus it will be useful to hide the splitter under some false panel.

If everything is done correctly, then the picture on both TVs should be clear and free of interference. Otherwise, a specific "snow" may appear due to the loss of a part of the signal or no picture at all.

Satellite TV

It often happens that even after the correct installation of the splitter, the image quality has noticeably deteriorated. This happens if you connect two TVs to one satellite dish. The problem arises due to the fact that the splitter picks up part of the signal anyway.

One of the options for solving this problem is to buy a splitter with a built-in signal amplifier. Such devices are much more expensive, but at the same time they are much more efficient than their simple counterparts.

It is also worth clarifying that all splitters with a built-in amplifier have different gains. In some cases, an oversized signal is just as useless as a weak one. Moreover, it can cause even greater picture distortion. This nuance is often encountered by those who want to connect two TVs to one Tricolor antenna or to Rainbow TV. Here you need to contact your provider's service specialist for help, who can measure the signal level and give advice on choosing a particular splitter with specific numbers.

If we are talking about an ordinary "Polish" antenna, then to improve the signal, you can connect an amplifier with a power supply, which will noticeably add image quality.

To do this, you need to make some changes in the already familiar scheme. It is necessary to remove the F-connector from the splitter entrance, then install the plug with the power supply, which comes with the "Polish" antenna, in the vacant space. After that, an adapter with an antenna socket ("female") should be mounted on the input and the connector with an amplifier should be connected.

Such a procedure will increase the gain, where, unlike satellite TV, the maximum value is not so important, so there should be no problems with an overabundance of the signal.

It is also useful to note that each subsequent TV significantly reduces the quality of reception. Therefore, for comfortable viewing of your favorite TV programs, it is better not to stint and purchase an additional antenna instead of "conjuring" with a splitter. This advice is especially relevant if the TV tower is located at a great distance from the receiver.

fb.ru

Your question:

How to connect two TVs to one cable?

The master's answer:

In order to connect multiple TVs to one cable, you can use several methods. The choice of method depends on the final purpose of the connection.

If you want to connect a pair of TVs to the same cable TV wire, then use the dedicated splitter. It is a tee that branches out the cable. Connect one end of the splitter to the cable itself, and all the others to your TVs using suitable wires.

If you have access to satellite TV the receiver is connected, then you will need to buy an additional splitter. The connection depends on which channel you have selected to connect the receiver to your TV. Splitters with VGA and DVI ports are available today. Connect it to the cable that comes from the receiver, and then connect the TVs to it. You should be aware that using additional adapters will allow you to interconnect the VGA, DVI and HDMI ports. Buy yourself a suitable set of such adapters. But remember that the use of such accessories will greatly reduce the signal quality. And also remember that with this connection method, all TVs will show the same channel.

You can use a VGA or DVI port splitter to connect all TVs to the same video card connector on your computer. In this case, the two devices will show the same channel. The best solution is to use both types of connection. To do this, connect a conventional antenna cable to two TVs using the method described above. Now connect them to the receiver. This method will help you switch modes from the receiver to the antenna and thus provide the ability to choose desired channel... If you want to connect two TVs to one satellite TV, then it is better to choose a company that installs the receiver at once for the whole entrance or at home.

Owners of several TVs in the house often wonder how to split the signal and not degrade the broadcast quality. A properly selected and connected antenna splitter creates a structure for wiring a television cable from one source without significant loss of signal power.

Views

There are several types of antenna splitters, but they all have the same external device consisting of metal case and connectors for connecting a cable. On the case, there is always a marking of the connectors:

Input (IN) - for the cable entering the room.
Output (OUT) - for the cable connecting the antenna splitter to each of the TVs.

According to their purpose, antenna splitters are divided into:

Dividers (splitters), with the help of which the TV signal is evenly divided into several outputs. Used for routing cables around the house or apartment.
Couplers (TAP), which differ from dividers by the presence of one through-outlet. This output allows you to serially connect another coupler to it without loss of quality. Designed for the organization of a television network in an apartment building.

It is worth paying attention to the important property of the dividers to pass the signal in reverse side and used as adders. This quality allows splitters to mix signals from several antennas of different frequency ranges into one cable, if their frequency specifications allow.

Specifications

When selecting any equipment, one must proceed from both the characteristics and the individual characteristics of its installation in a particular situation. Antenna splitters were no exception. How to choose the correct divider for its parameters?

Antenna splitter specifications:

Bandwidth... Shows transmitted by divisor frequency range... For terrestrial TV operating frequency the divider should be within 5-1000 MHz, for satellite - from 5 to 2500 MHz. A satellite splitter can be used to transmit terrestrial digital and analogue signal.

Number of outputs. Antenna splitter can include up to eight of them. Select the equipment based on the number of TVs to be connected. You can connect a splitter with a large number of outputs to expand your television network.

Attenuation level. An important indicator that determines the amount of reduction in the power of the transmitted signal. The lower this indicator, the less the output losses will be.

The presence of an RF amplifier. An antenna splitter with a built-in RF amplifier is called active. Such a divider is able not only to maintain the power of the incoming signal, but also to increase it. It is worth considering the need to connect the power supply for the active divider.

If you intend to split the signal between two TVs, it is enough to get a passive splitter with two outputs and a good TV cable. The attenuation will be 3-3.5 dB at each output, which will not have a significant impact on quality.

If the plans are to divide the signal into three or more TVs, then to select an amplifier it is necessary to draw up a wiring diagram so that the input to each TV has the same signal level. It is imperative to take into account the attenuation level not only in the divider, but also in the cable. Usage active amplifier in this case, it guarantees a reduction in splitting losses, length and quality of the cable used.

DIY antenna splitter

The antenna splitter circuit does not contain anything complicated, and it is technically quite possible to make it yourself. Any divider consists of a bridge with a ferrite transformer and capacitors. But is it worth making it so difficult? The manufactured device will be suitable only for splitting the analogue television signal, and ferrite rings can only be found in specialized stores.

It makes sense to constructively modify an inexpensive Chinese-made antenna splitter or convert a passive divider into an active one. Many Chinese no-name manufacturers save on installing additional resistors and SMD capacitors. Your best bet would be to buy a divider from trusted brands like Alda, Rexant or Lans.

This requires a splitter or CRAB, which in translation into ordinary human language means "consumer household cable splitter". Nowadays, you can buy it at any hardware store, but before you could make it yourself from radio components. This simple device consists of a body and three or four resistances with leads to sockets for connecting television receivers.

What is a splitter

A cable splitter is a device consisting of resistances calculated in a certain way, which serve to correctly match the wave impedances of the feeders of one antenna and several televisions. They provide the lowest possible signal attenuation.

You should know that always three TVs should be connected to a splitter with three outputs.

If you do it differently, for example, connect two or one instead of three TVs, then for normal operation of the device you need to connect a 75 Ohm ballast resistor to a free output.

When choosing a splitter, first of all, you should look in the attached instructions for the frequency range that it is capable of passing.

If you have cable TV at home, then you can make a vain purchase - not every splitter will pass the high-frequency channels of decimeter waves used by operators to relay the signal.

Number of connected TVs

If necessary, 2,3 or 4 TVs can be connected to the splitter from one antenna. Large quantity already impractical - very large signal attenuation:

one TV - the real power of the TV signal is 1/1;
two - signal strength 1/2;
three - signal power 1/3;
four - signal strength 1/4.

You can connect more than four TVs to one antenna, but you have to install a signal amplifier. On sale there are a variety of prices, quality and technical specifications devices that allow you to do this without losing image quality.

Connection process

First of all, you need to decide on the place of installation of TV sets, measure and cut off the required amount antenna cable... At the ends of the cable on the TV side, attach the antenna plugs, but do not connect. Many splitters from different manufacturers have jacks different types... Basically, these are screw sockets, connected with a nut with an inserted and pre-stripped end of the cable. At the same time, the central core is inserted into the hole of the screw socket, after which you need to screw the nut so that the cable sheath is pressed against the CRAB body.

Some devices have ordinary sockets for connecting plugs, and accordingly you should have them 2,3,4 and so on, that is, the corresponding number.

Old manufacturers still make types of splitters where it is necessary to use a soldering iron or screwdriver when connecting two, three or four TVs. In this case, the braid and central cores of the cables must be soldered into special contacts or fixed with screws.

Observe safety precautions when connecting multiple TVs to one antenna through a splitter. De-energize all household appliances before completing the work on connecting cable plugs to them.

Modern TV tuners have unlimited possibilities: there is no problem for them to transmit a signal from one source to several receivers at once without quality loss. Therefore, there is no such problem as connecting two TVs to one satellite dish for the receiver, you just need to choose the right TV tuner in order to successfully complete the task.

To successfully implement our plan and connect two TVs to one receiver, a home master will need:

simple set of cable stripping tools;
a parabolic antenna or just a dish;
TV tuner;
splitter or splitter for two outputs;
two TVs;
a set of necessary cables.

When all the components have been purchased, then you can proceed with the installation of the entire system, but before that, a few words about the devices.

Signal splitter

The main task of this device in our case is to divide the received signal into equal parts and redirect it to two TVs, therefore, when buying a splitter, you must carefully study its characteristics. The only drawback of this device is that when the signal is divided into 2 TVs, loss of quality.

On the body of the splitter, the manufacturer indicates the value of the signal attenuation, the lower it is, the better the splitter is.

TV tuner

Today receivers can transmit a signal from several devices at once and send them to their destination. When choosing a tuner in a store, pay attention to maximum resolution supported by the product to connect to.

It is worth clarifying the possibility of transfer digital channels , do not save - it is better to take a satellite receiver latest model, which has modern improvements, than then buy additional devices for. The best option when the device has ports for connecting S-Video, VGA, DVI and HDMI. Be sure to find out from the seller how to connect two TVs to this model, which channels are better to use.

The attached operating instructions must necessarily contain a schematic drawing of such a connection to one plate with a step-by-step description of all actions.

Digital TV tuner DTV-09

Configuring system components

Before connecting the tuner, you need to configure it:

we connect the receiver to the home electrical network;
we connect the product to the computer via USB port;
and connect it to a special connector on the tuner;
install software that is attached to the product;
run the program and adjust the operating parameters.

Only after careful tuning, we start connecting the connected tuner to TVs. For this, it is better to use the digital inputs in order to maintain the much desired image quality.

Let's say that one TV is installed in the living room, and another connected object, for example, in the son's room: then we connect the nearest TV to the receiver with an HDMI cable. We turn on the TV set in the hall and start setting it up:

go to the menu;
select the signal source;
we indicate the connector to which the connection was made from the tuner;
we make the setting according to the instructions of the product, as a rule, choose auto scan which modern models perform independently;
after the list of channels appears, we filter out low-quality and duplicates, leaving only those that are necessary for further viewing.

Now it's time to tell you how to connect a second TV to the receiver. We measure the shortest distance a good option- to drill the adjacent wall, but this is not always possible. The cable must be laid along the plinth so as not to touch it when moving around the apartment.

On sale there are special skirting boards with production for a cable, from above they are closed with a lid, which is very convenient - the wires are hidden and do not disturb the interior.

Setting up the second TV is carried out in the same way with the obligatory indication of the connected cables, in the event that they are used by more than one.

Connection algorithm

There are several different ways how to connect two TVs to one tuner in an apartment or a private house, using a special cable that is necessary.

Option number 1

For this we use HF or frequency television cable, which connects to the RF OUT output on the rear panel of the receiver, and its other end to the antenna input on the TV. After that, it remains only to make the TV settings according to the operating instructions for this model.

Option number 2

We connect two TVs through one receiver with RF modulator application... Many modern tuners do not have a built-in analogous modulator and RF OUT output, so in this case we need:

remote frequency device;
low-frequency RCA cable with tulip connectors;
coaxial cable with resistance 75 Ohm;
F-connectors and the same plugs.

For a separate power supply to the modulator, a separate socket with a voltage of no more than 230 V is required.

We connect tulips to the corresponding outputs on the tuner and modulator, connect the TV cable to the RF OUT output on the RF device, and screw the F-plug onto the RF IN input - it is included in the kit. We connect the other end of the coaxial cable to the IN output of the splitter, you need to purchase it in advance splitter with two such outputs... After all the manipulations, we connect all the equipment to home network and set up the TVs one by one.

Option number 3

We connect the satellite tuner using RCA cables which can be used when simultaneously connecting two TVs to one receiver together with HDMI. You will need a special SCART-RCA adapter, and when setting up a TV connected with this cable, you need to change the input settings. The scheme of such a connection is simple, it is carried out economically - no need to buy expensive equipment.

But at the same time, there are negative aspects: the cable length should not exceed 15 m, otherwise distortions will go or the image will disappear altogether. In a city apartment, such a footage should be enough - you don't have to solder two wires, which negatively affects the quality of the received signal.

Connecting with a fork into two TVs is not the limit - there are circuits for connecting four and eight receivers, but every user should know that if football is playing on one TV, then on the others, no matter how many of them are in the house, there will be a similar program. You can change channels only in the room where the satellite receiver is installed, but many people buy an additional radio remote control to solve this problem. To watch different gears- it is necessary for each TV separately, but these are completely different schemes and a separate topic for discussion.

Categories

Popular