Connecting zyxel keenetic giga ii. Description of the Zyxel Keenetic Giga II router, its connection, firmware and configuration. Configuring a backup connection

The Zyxel Keenetic Giga II Internet Center is multifunction device, with which you can build a home or office network with Internet access and Wi-Fi access. In addition to basic functions, it has a number of additional opportunities that go far beyond the ordinary router, making this device interesting for the most discerning user. To realize these possibilities as fully as possible, the router must be able to properly configure. This will be discussed further.

Before starting the configuration, you need to prepare the router for the first time. This preparation is standard for all devices of this type. You need to choose a place where the router will be located, unpack it, connect the antennas and connect it to a PC or laptop, and connect the cable from the provider to the WAN connector. If you are using a connection to a 3G or 4G network, you must connect a USB modem to one of the available connectors. Then you can proceed to configure the router.

Connecting to the Zyxel Keenetic Giga II web interface

No special tweaks are required to connect to the web interface. All you need to do is:


After completing these steps, the first time you connect, the following window will open:


The further course of the setup will depend on which of the two options offered in this window the user chooses.

NDMS - the operating system of the Internet center

One of the product features lineup Keenetic is that their operation is controlled not just by firmware, but by the whole operating system - NDMS. It is its presence that turns these devices from commonplace routers into multifunctional Internet centers. Therefore, it is very important to constantly keep the firmware of your router up to date.

NDMS OS is built on modular type... It consists of components that can be added or removed at the discretion of the user. You can view the list of installed and available components for installation in the web interface in the section "System" in the tab "Components"(or on the tab "Updates", the location is affected by the OS version).


By ticking the required component (or unchecking) and clicking on the button Apply, you can install or uninstall it. However, this must be done very carefully so as not to accidentally remove a component necessary for the normal functioning of the device. Such components are usually marked "Critical" or "Important".

The presence of a modular operating system makes the configuration of Keenetic devices extremely flexible. Therefore, depending on the user's preferences, the web interface of the router can have completely different subsections and tabs (except for the basic ones). Having understood this important point, you can proceed to the direct configuration of the router.

Quick setup

For those users who do not want to delve deeply into the intricacies of configuration, the Zyxel Keenetic Giga II provides the ability to set the basic parameters of the device in a few clicks. But at the same time, you still need to first look into the contract with the provider and find out the necessary details about your connection. To start the quick configuration of the router, you must click on the corresponding button in the settings window that appears next after authorization in the device's web interface.


Next, the following will happen:


As you can see, setting up the device really happens very quickly. If the user needs additional functions the Internet center, he can continue it manually by pressing the button "Web configurator".

Manual setting

Those who like to delve into the parameters of the Internet connection do not need to use the function on their own. quick setup router. You can directly enter the device's web configurator by clicking on the corresponding button in the initial settings window.

Then you need to:


After that, you can start creating an interface for connecting to the Internet. To do this, you need to select the required type of connection (according to the agreement with the provider) and click on the button "Add interface".


Then you need to set the necessary parameters for connecting to the Internet:


After entering the parameters, click on the button Apply, the router will receive new settings and will be able to connect to the Internet. It is also recommended to fill in the field in all cases "Description", for which you need to come up with a name for this interface. The router's firmware allows the creation and use of multiple connections, and thus you can easily distinguish between them. All created connections will be displayed in the list on the corresponding tab in the Internet settings menu.


From this submenu, if necessary, you can easily edit the configuration of the created connection.

Connection to 3G / 4G network

The presence of USB ports makes possible connection Zyxel Keenetic Giga II to 3G / 4G networks. This is especially convenient if the device is planned to be used in rural areas or in the country where there is no wired internet... The only condition for creating such a connection is the coverage of the mobile operator, as well as the installed necessary NDMS components. The fact that this is so is evidenced by the presence of a tab "3G / 4G" In chapter "Internet" router web interface.


If this tab is missing, the necessary components need to be installed.

The NDMS operating system supports up to 150 models of USB modems, so problems with their connection are rare. You just need to connect the modem to the router for the connection to be established, since its main parameters are usually already written in the modem's firmware. After connecting, the modem should appear in the list of interfaces on the tab 3G / 4G and in the general list of connections on the first tab of the section "Internet"... If necessary, you can change the connection parameters by clicking on the name of the connection and filling in the appropriate fields.


However, practice shows that the need manual setting connecting to mobile operator occurs infrequently.

Configuring a backup connection

One of the advantages of the Zyxel Keenetic Giga II is the ability to use multiple Internet connections at the same time through different interfaces. In this case, one of the connections acts as the main one, and the rest are backup. This function is very handy in case of unstable connection with providers. To implement it, it is enough to set the priority of connections on the tab "Connections" section "Internet"... To do this, you need to enter digital values ​​in the field "A priority" list and click "Save Priorities".


Larger value means higher priority. Thus, from the example in the screenshot, it follows that the main thing is to connect via wired network with a priority of 700. If the connection is lost, the router will automatically establish a connection to the 3G network via a USB modem. But at the same time, he will constantly try to restore the main connection, and as soon as this becomes possible, he will switch to it again. It is possible to create a similar pair from two 3G connections from different operators, as well as set a priority for three or more connections.

Change wireless settings

By default, the Zyxel Keenetic Giga II already has a created Wi-Fi connection, which is quite workable. The name of the network and the password to it can be found on the sticker on the bottom of the device. Therefore, in most cases, setting up a wireless network boils down to changing these two parameters. To do this, you must:


After saving the settings, the network will start working with the new parameters. They are enough for most users.

At the end of the review, I would like to emphasize that the article touched on the topic of only key points in setting up Zyxel Keenetic Giga II. However, the NDMS operating system provides the user with many additional options for using the device. A description of each of them deserves a separate article.

In order to get into the web interface of the router, you need to open your Internet browser and type 192.168.1.1, User Name in the address bar admin (username), Password - 1234 (provided that the router has factory settings and its IP has not changed).

Changing the factory password

For security reasons, it is recommended that you change the factory password. By default: Login admin, password 1234. In the router interface, go to the “ System", Further password. In field "New Password" enter New Password... It must be repeated in the next field. Then we save the settings by pressing the button " Apply».

Setting up Wi-Fi on the router

Wi-Fi.

  1. In the window that appears in the field Network name (SSID) enter the name of your network (any)
  2. In field Use connection protection choose WPA-PSK + WPA2-PSK
  3. In field Network key enter your password to access the network (any)
  4. In field Channel: choose Auto
  5. Apply.

Setting up a network connection

NAT when automatically obtaining an IP address (DHCP)

  1. At the bottom of the page, select a section Internet
  2. In the window that appears, click on Broadband connection (ISP)
  3. In field Configuring IP Settings choose Automatic
  4. In field MTU size enter 1400
  5. After filling in these fields, click the button Apply.

Setting up an Internet connection

At the top of the page, select the tab Authorization.

  1. In field Type (protocol used) choose PPTP
  2. In field Connect via choose Broadband connection (ISP)
  3. In field Server address enter Server name or address(ask the provider)
  4. In field Username enter your login from the contract
  5. In field Password enter your password from the contract
  6. In field Authentication method choose Auto
  7. Service Name, Hub Name, Description- you can leave it blank
  8. After filling in all the fields, click the button Apply.

PPPoE connection setup (Rostelecom, Dom.ru)

InternetAuthorization»

  1. Internet access protocol: PPPoE
  2. Username : Your login by agreement
  3. Password: Your contract password
  4. Save the settings with the button Apply.

Configuring L2TP connection (Beeline)

In the router interface, select the tab on the left " Internet", In the list that opens, select" Authorization»

  1. Internet access protocol: L2TP
  2. Description: connection name
  3. Server address: server name or address (specified in the contract)
  4. Username : Your login by agreement
  5. Password: Your contract password
  6. Authentication method: Auto
  7. Save the settings with the button Apply.

  1. Wireless antennasWi-Fi Two omnidirectional antennas. The recommended position of the supplied antennas is vertical.
  1. (Wireless LAN Control) buttonWi-Fi) The button allows you to quickly and safely connect to a secure network Wifi router Wi-Fi 802.11g / n wireless devices that support the WPS standard, such as computers and laptops with an operating room Microsoft system Windows.

Short press Starts the Quick Connection (WPS) function
Pressing for more than 3 seconds Turns on or off wireless network

  1. Reset button (Reset custom settings) Use this button if you need to configure the router again or you have lost the password to access it. To reset the settings, press the button with a pointed object and hold it down for about 10 seconds, until all lights on the router go out. The power indicator will start blinking, and after half a minute, the Keenetic will boot up with the default settings.
  1. FN Button (Flexible Button) In the web configurator of the Keenetic, you can assign one or several functions to this button. By default, the button is designed to safely disconnect all USB drives connected to the router.
  1. Network connectors "0 ... 4" Five network connectors for connecting home devices and the Internet. By default, the yellow connectors "1 ... 4" are for your home network and the blue connector "0" for the Internet.
  1. Power Switch and Connector Power switch and power adapter connector supplied. The router is designed for continuous operation and does not require daily power outages. If you need to turn off the router, for example during a long break in use, it is recommended that you also unplug the power adapter from the electrical outlet.


2 USB Multifunction Host Connector - Located on the side of the router. Connector for compatible USB devices such as USB modems mobile internet 3G / 4G, USB sticks, USB printers. You can find the current list of compatible USB devices on the Keenetic Omni router page by visiting the ZyXEL website.

8. Power indicator (Status)

9. Indicators 0, 1, 2, 3, 4 (Connected to network connectors)


10. (Wireless Wi-Fi) indicator

12. Indicator (USB connection)

Router connection

  • Choose a suitable location for your router. It is recommended to place the router at the center of the wireless network.
  • Adjust the position of the antenna. An upright position is often best.
  • Connect your computer to local network via the LAN (home network) ports of the router (if you already have a wireless network adapter and want to use a wireless network connection, you can skip this step)
  • Connect incoming Ethernet cable to the INTERNET port of the router
  • Connect the power adapter to the power adapter on the router and plug the other end into a power outlet.

Setting up a computer to connect to a router:

  • In your computer's TCP / IP settings, select.

To configure the router, you need a computer with network adapter Ethernet or Wi-Fi configured to automatically obtain an IP address (in your computer's TCP / IP settings, select Obtain an IP address automatically).
1. Connect the router to a power outlet using the supplied power adapter. Wait until the POWER indicator of the router stops blinking and stays on.
2. Connect the router to the computer from which the configuration will be performed. To do this, connect connector "1" on the router to the Ethernet adapter of your computer using the supplied network cable... Turn on your computer and wait for the operating system to load. If the connection to the computer is correct, the “1” indicator on the router will light up.
To access the router configuration, open a web browser and enter the default address http://192.168.1.1 in address bar then press ENTER. A window will open with the choice of the type of router settings. In this window, you must select the item Web configurator.





Immediately after choosing the setting option, a window will appear in which you will be asked to create a password to log into the router to prevent unauthorized access to the system settings.
In both windows, you must enter the same password, in case of mismatch, a message about password mismatch will appear.

After that, you will be taken to the main settings and diagnostics page. This window displays general information about the connection status, as well as the settings menu items.

DHCP configuration


To configure automatic obtaining of an IP address (DHCP) by a router, you must click on the button
Then you need to select the type of connection Broadband connection which is to be configured (by double clicking on it with the left mouse button):

After selecting the connection type, a new window will open in which you can configure the automatic obtaining of an IP address.

Use connector: In this section, you can select the port that will be the main one for communication with your provider. When configuring, the default port should be marked "0". There should be empty cells in front of other ports.
Pass tagsVLAN ID: This field can be left blank.
Turn on:
Description: In this field, you can set the connection name, how it will be displayed in the router settings field. You can leave the default name in this field (broadband connection) or change it to DHCP.
Network ID(VLAN ID): Leave default parameter 2
SettingsIP: In this setting item, you can select the type of receiving IP, must be selected Automatic.
IPaddress:
Subnet mask: not available (for automatic tuning IP settings)
Main gate: not available (when automatically configuring IP settings)
DNS 1,2,3: These fields should be left empty, because when automatically receiving an IP address, your router will automatically receive this parameter as well.
MAC-address: At this point, you can choose how to use the MAC address ( unique identificator network device). The value should be Default.
Device name: At this point you can change the name of your router that will be displayed on the Internet.
The sizeMTU: Should be set to 1500
Do not reduceTTL: In this menu item, the selection must be deselected.
After entering the settings, you must click Apply... Then you can proceed to setting up the Wi-Fi connection.

PPOE connection setup


If you are using a PPPoE connection, then you should select
then, in the window that appears, select the tab for settings PPPOE / VPN and in this window click the button Add connection


After that, a new window will appear in which you need to configure the connection using the PPPOE protocol.

Turn on: This item must be selected (activates this type of connection).
Use to connect to the Internet: This item must be selected. If the selection is cleared, the router will not use the dedicated port for communication with the provider, but will use this port as a local one (for communication within the local network).
Description: In this field, you can set the connection name, how it will be displayed in the router settings field. It is recommended to specify PPPOE connection.
Type (protocol): At this point, you must select the type of PPPOE tunnelled connection. (PPPTP options are also available, L2TP - not used in your network)
Connect via: At this point, you must select the network connection that will be used to establish the connection. You must choose Broadband connection (ISP)
Service name:
Hub name: This field must be left blank. (not used)
Service address: This field is unavailable for this type of connection.
Username: Login connections provided to you by your provider.
Password: In this paragraph, you must specify Password connections provided to you by your provider.
Authentication method: This paragraph should contain the value Auto .
Data encryption:
UseCCP: This item is not available with this connection.
SettingsIP: This item is responsible for the type of obtaining an IP address. There must be a value Auto .
IPaddress: This item is not available with this connection.
RemoteIPaddress: This item is not available with this connection.
DNS 1,2,3: These items are responsible for specifying specific DNS servers... But due to the fact that all settings are assigned automatically, there is no need to specify values ​​in these fields.
Auto-tuningTCP-MSS: This item is responsible for auto-tuning the size of data fragments. This item must be enabled.
After setting up the connection via PPPOE, you need to click the APPLY button, after which you can go to the Wi-Fi network settings.

Setting up a wireless connection


For settings wireless connection it is necessary to press the assignment in the main menu
In the window that appears, the tab should be selected Access point.


Enable hotspot: This item is intended to enable / disable broadcasting of the radio module. This item must be enabled.
Network name(SSID): In this field, you must enter the name of your network (the name of your network will be displayed in the list of available networks). By default, this field contains the name of the router model.
HideSSID: If this item is not highlighted, then the name of your network will be visible in the list of networks, if the item is highlighted (activated) then your network will be hidden, and connection to it will be possible only by manually entering the network name. It is better to leave this item unselected.
Network protection: Here you can select the type of encryption to be used. It is advisable to use WPA2-PSK since this type of encryption is the most reliable and supports the 802.11n broadcast standard (the fastest).
Network Key: Here you can specify a password with a length of 8 to 63 characters in ASCII encoding (that is, it is permissible to use uppercase and lowercase letters and numbers of the Latin alphabet).
Key 1,2,3,4:
Default key: At this type encryption (WPA2-PSK) not available
Standard: Please select 11bgn mode. This mode allows all wireless stations of the 802.11b, 802.11g and 802.11n standards to connect to the router.
Channel: This field is set operating frequency which you are going to use. The default mode is Auto, thus, the access point itself in automatic mode will choose the most suitable channel . This parameter should be left in Auto mode.
Signal strength: In this item, you can set the broadcast signal strength of the radio transmitter. You must put 100%.
After setting the settings, click the APPLY button. After that, your router is fully configured to work on our network.


  1. Wireless antennasWi-Fi Two omnidirectional antennas. The recommended position of the supplied antennas is vertical.
  2. (Wireless LAN Control) buttonWi-Fi) The button allows you to quickly and safely connect wireless devices Wi-Fi 802.11g / n that support the WPS standard, such as computers and laptops with Microsoft Windows operating system, to the router's secure Wi-Fi network.

Short press Starts the Quick Connection (WPS) function
Pressing for more than 3 seconds Enables or disables the wireless network

  1. Reset button (Reset custom settings) Use this button if you need to configure the router again or you have lost the password to access it. To reset the settings, press the button with a pointed object and hold it down for about 10 seconds, until all lights on the router go out. The power indicator will start blinking, and after half a minute, the Keenetic will boot up with the default settings.
  1. FN Button (Flexible Button) In the web configurator of the Keenetic, you can assign one or several functions to this button. By default, the button is designed to safely disconnect all USB drives connected to the router.
  1. Network connectors "0 ... 4" Five network connectors for connecting home devices and the Internet. By default, the yellow connectors "1 ... 4" are for your home network and the blue connector "0" for the Internet.
  1. Power Switch and Connector Power switch and power adapter connector supplied. The router is designed for continuous operation and does not require daily power outages. If you need to turn off the router, for example during a long break in use, it is recommended that you also unplug the power adapter from the electrical outlet.

(USB multifunction host connector) Located on the side of the router. Connector for compatible USB devices such as USB 3G / 4G mobile Internet modems, USB drives, USB printers. You can find the current list of compatible USB devices on the Keenetic Omni router page by visiting the ZyXEL website.


8.Power indicator (Status)

9. Indicators 0, 1, 2, 3, 4 (Connected to network connectors)


10. (Wireless Wi-Fi) indicator

12. Indicator (USB connection)

Router connection

  • Choose a suitable location for your router. It is recommended to place the router at the center of the wireless network.
  • Adjust the position of the antenna. An upright position is often best.
  • Connect your computer to your local area network through the LAN (home network) ports of the router (if you already have a wireless network adapter and want to use a wireless network connection, you can skip this step)
  • Connect the incoming Ethernet cable to the INTERNET port of the router
  • Connect the power adapter to the power adapter on the router and plug the other end into a power outlet.

Setting up a computer to connect to a router:

  • In your computer's TCP / IP settings, select.

To configure the router, you need a computer with an Ethernet or Wi-Fi network adapter configured to automatically obtain an IP address (in the TCP / IP settings of your computer, select Obtain an IP address automatically).
1. Connect the router to a power outlet using the supplied power adapter. Wait until the POWER indicator of the router stops blinking and stays on.
2. Connect the router to the computer from which the configuration will be performed. To do this, connect the connector "1" on the router to the Ethernet adapter of your computer using the supplied network cable. Turn on your computer and wait for the operating system to load. If the connection to the computer is correct, the “1” indicator on the router will light up.

To access the router settings, open a web browser and enter the default address http://192.168.1.1 in the address bar then press ENTER. A window will open with the choice of the type of router settings. In this window, you must select the item Web configurator.



Immediately after choosing the setting option, a window will appear in which you will be asked to create a password to log into the router to prevent unauthorized access to the system settings.


In both windows, you must enter the same password, in case of mismatch, a message about password mismatch will appear.

After that, you will be taken to the main settings and diagnostics page. This window displays general information about the connection status, as well as the settings menu items.


CustomizationDHCP

To configure automatic obtaining of an IP address (DHCP) by a router, you must click on the button


Then you need to select the type of connection Broadband connection which is to be configured (by double clicking on it with the left mouse button):


After selecting the connection type, a new window will open in which you can configure the automatic obtaining of an IP address.


Use connector: In this section, you can select the port that will be the main one for communication with your provider. When configuring, the default port should be marked "0". There should be empty cells in front of other ports.

Pass tagsVLAN ID: This field can be left blank.

Turn on:

Description: In this field, you can set the connection name, how it will be displayed in the router settings field. You can leave the default name in this field (broadband connection) or change it to DHCP.

Network ID(VLAN ID): Leave default parameter 2

SettingsIP: In this setting item, you can select the type of receiving IP, must be selected Automatic.

IPaddress:
Subnet mask: not available (when automatically configuring IP settings)
Main gate: not available (when automatically configuring IP settings)

DNS 1,2,3: These fields should be left empty, because when automatically receiving an IP address, your router will automatically receive this parameter as well.

MAC-address: In this item, you can select the way to use the MAC address (unique identifier of the network device). The value should be Default.

Device name: At this point you can change the name of your router that will be displayed on the Internet.

The sizeMTU: Should be set to 1500

Do not reduceTTL: In this menu item, the selection must be deselected.

After entering the settings, you must click Apply... Then you can proceed to setting up the Wi-Fi connection.

PPOE connection setup

If you are using a PPPoE connection, then you should select


then, in the window that appears, select the tab for settings PPPOE / VPN and in this window click the button Add connection


After that, a new window will appear in which you need to configure the connection using the PPPOE protocol.


Turn on: This item must be selected (activates this type of connection).

Use to connect to the Internet: This item must be selected. If the selection is cleared, the router will not use the dedicated port for communication with the provider, but will use this port as a local one (for communication within the local network).

Description: In this field you can set the connection name, how it will be displayed in the router settings field. It is recommended to specify PPPOE connection.

Type (protocol): At this point, you must select the type of PPPOE tunnelled connection. (PPPTP options are also available, L2TP - not used in your network)

Connect via: At this point, you must select the network connection that will be used to establish the connection. You must choose Broadband connection (ISP)

Service name:
Hub name: This field must be left blank. (not used)
Service address: This field is unavailable for this type of connection.

Username: Login connections provided to you by your provider.
Password: In this paragraph, you must specify Password connections provided to you by your provider.

Authentication method: This paragraph should contain the value Auto .

Data encryption:
UseCCP: This item is not available with this connection.

SettingsIP: This item is responsible for the type of obtaining an IP address. There must be a value Auto .

IPaddress: This item is not available with this connection.
RemoteIPaddress: This item is not available with this connection.

DNS 1,2,3: These items are responsible for specifying specific DNS servers. But due to the fact that all settings are assigned automatically, there is no need to specify values ​​in these fields.

Auto-tuningTCP-MSS: This item is responsible for auto-tuning the size of data fragments. This item must be enabled.

After setting up the connection via PPPOE, you need to click the APPLY button, after which you can go to the Wi-Fi network settings.

Setting up a wireless connection

To set up a wireless connection, in the main menu, press the assignment

In the window that appears, the tab should be selected Access point.



Enable hotspot: This item is intended to enable / disable broadcasting of the radio module. This item must be enabled.

Network name(SSID): In this field, you must enter the name of your network (the name of your network will be displayed in the list of available networks). By default, this field contains the name of the router model.

HideSSID: If this item is not highlighted, then the name of your network will be visible in the list of networks, if the item is highlighted (activated) then your network will be hidden, and connection to it will be possible only by manually entering the network name. It is better to leave this item unselected.

Network protection: Here you can select the type of encryption to be used. It is advisable to use WPA2-PSK since this type of encryption is the most reliable and supports the 802.11n broadcast standard (the fastest).

Network Key: Here you can specify a password with a length of 8 to 63 characters in ASCII encoding (that is, it is permissible to use uppercase and lowercase letters and numbers of the Latin alphabet).

Key 1,2,3,4:

Default key: This type of encryption (WPA2-PSK) is not available

Standard: Please select 11bgn mode. This mode allows all wireless stations of the 802.11b, 802.11g and 802.11n standards to connect to the router.

Channel: This field sets the operating frequency that you are going to use. The default mode is Auto, thus, the access point will automatically select the most suitable channel on its own . This parameter should be left in Auto mode.

Signal strength: In this item, you can set the broadcast signal strength of the radio transmitter. You must put 100%.

Turn onWMM: This item is needed for the best distribution of priorities in packaging (QOS). This item must be enabled.

After setting the settings, click the APPLY button. After that, your router is fully configured to work on our network.


Notes.
1. Experienced users can update the firmware version of the router to a more up-to-date one.

2. In case of losing control of the router (the web configurator page (192.168.1.1) is not available, it will help you restore operating system router.

Let's move on to setting up.
The router is configured using a browser via the Web interface. Physically, for configuration, you can connect to the router using either an ethernet cable or Wi-fi.

1. If not via Wi-fi, connect the Ethernet cable coming to your apartment to the port WAN Your router.

2. Reset the settings of the network card, or wifi adapter on the computer if other devices were previously connected to it. For this in Windows XP Start, Control Panel, Network connections... V Windows 7 left click on the button Start, select Control Panel, Further Network and Internet, then Network Control Center and general access, Change adapter settings... In the opened window right click mouse click on the icon LAN connections or wireless connection and in context menu select item Properties.

Left-click once Internet Protocol TCP / IP(for Windows 7 - Internet Protocol Version 4 (TCP / IPv4)) and press the button Properties.

Adjust the settings in accordance with the ones shown in the figure below:

3. If not wi-fi, connect the Ethernet cable between the network card of the computer and one of the ports of the router, for example, port number 1, as shown in the figure.

4. Launch your browser and in the address bar enter http://192.168.1.1 and press Enter... In the appeared authorization window in the field User Name enter admin, field Password enter 1234 and press the button OK.

5. Customization network connection.

.

Internet.
Broadband connection (ISP).

3) In the field Configuring IP Settings choose Automatically.
4) In the field MAC address choose Default
5) In the field MTU size enter 1400 .

Note. When you configure the IP parameters "Automatic", all IP addresses and routing will be sent to the router automatically.
After filling in all the fields, click the button Apply.

6. Setting up an Internet connection.

At the top of the page, select the tab PPPoE / VPN... 1) In the field Type (protocol used) choose L2TP.
2) In the field Connect via choose Broadband connection (ISP).
3) In the field Server address enter l2tp.freedom.
4) In the field Username
5) In the field Password
6) In the field Authentication Algorithm choose CHAP... After filling in all the fields, click the button Apply.

7. Wi-Fi setup.

Peculiarities Wi-Fi settings in the updated Keenetic II series.

The updated Keenetic II series has an easy-to-access button Wi-Fi on the top cover of the case, combining functions WPS(WPS (Wi-Fi Protected Setup) is a standard designed to simplify the process of setting up a wireless network.) Wi-Fi module device with a long (3 sec.) press. Also, in the settings of the router, it became possible to change the actions of the buttons Wi-Fi and Fn.

Wi-Fi.
1) In the window that appears, in the field Network name (SSID) enter your login to access the network from the Subscriber's Registration Card.
2) In the field Use connection protection choose WPA-PSK + WPA2-PSK.
3) In the field WPA key enter your password to access the network from the Subscriber's Registration Card.
4) In the field Radio channel number: choose 11 or 12 (If the network is not loaded, you can also auto).
5) After filling in all the fields, click the button Apply.
Note 1. If there are devices apple(iPhone, ipad, macbook) then the channel is selected up to 10.
Note 2. If the router was configured via wi-fi, for further configuration you will have to reconnect to the router by following the steps in paragraph 12 of this manual.

8. Configuring IGMP for viewing IPTV.

At the bottom of the page, select a section home network ... At the top of the page, select the tab IGMP Proxy... Check if the settings are correct according to the screenshot below:

9. Allocating a port for an STB set-top box.

If you need to allocate a port for connecting an STB set-top box for viewing IPTV (in this case, the port of the router to which the set-top box is connected will be removed from the control VLAN and the set-top box will be connected in the same way as connecting through a separate switch / switch), do the following:
1) At the bottom of the page, select a section Internet.

2) In the window that appears, click on Broadband connection (ISP).
3) In the new window, check the box Use connector under the port to which the STB is connected. In our example, this is port 4.
4) Press the button Apply.

10. Customize your Wifi map on a computer to access the network.

To do this, left-click once on the network card icon in the lower right corner of the screen (next to the clock).

In the window that appears, click the button To plug and enter Wireless access key which you asked earlier.

In windows 7/8

We select our connection, click on it. We put a tick “connect automatically” and click “connect”.

If our connection is with an exclamation mark, it means it is without a password, Anyone can connect to your network.

Enter the security key. Click "OK".

If everything is in order, we will observe the following picture.

Fitting © 2021 Tech Look - Gadgets. Android device. Antiviruses. Security. Graphics. Internet. Mobile devices